Outstanding photos and description!!
Thank you very much for taking the time read this.Outstanding photos and description!!
So there it is, that's the amount of lather that I think of as a minimum to provide good protection and slickness. I hope this shows why getting enough proto lather at the beginning is so important and I only did two water additions so this is still doable every day. I think the resulting lather speaks for itself, it accomplishes the goal of being just short of dripping wet without loosing skin protection. This is only possible by loading enough soap, a merely wet lather is just a short cut that is going to cost you later in skin irritation. Lather like this almost erases any blade feel present, like little ball bearings between the blade and your face. Poor lather may glide well and fool you into thinking that everything is fine, but will not protect you from the blade edge.
I hope this is helpful to somebody. This is not intended as a comprehensive lathering tutorial and I have omitted some steps as my primary objective is to demonstrate the process of generating a proto lather, the lathering steps are just thrown in extras and assume that the reader knows how to add water and integrate it.
It's just because I wasn't shaving and wanted to show how much soap should be in the brush before building the lather. The point being that if you load too lightly and over hydrate that, you have no protection just wet slickness. Maybe I should have taken one picture of the brush with a load of lather and said, at least this much and been done with it. I didn't and I can't edit it now, I acknowledged that this was flawed a couple posts up.I don't quite understand why you are using a stick like that in the first place. @Tillerman explains the process perfectly. The beauty of a shave stick is its simplicity of use.
Ahhh! The lightbulb just went on for me.It's just because I wasn't shaving and wanted to show how much soap should be in the brush before building the lather. ....
The Lea stick, I think La Toja is the same, is the easiest thing I have lathered! Rubbing a Haslinger puck on my face would be a close second.I have to add that I have used a shave stick less than a dozen times, but I have fallen in love with the process. Have a Stirling tuxedo that I didn't care for for bowl lathering, but works great on my face. Can't wait to get a variety of sticks.
ThanksThe Lea stick, I think La Toja is the same, is the easiest thing I have lathered! Rubbing a Haslinger puck on my face would be a close second.
My process is rubbing the stick on my face then lathering with a dampish brush until my face is covered then dip my brush in water and lather until I get the desired hydration. I prefer a rather wet but not runny lather. As I shave the lather will begin drying a bit and I dip and keep it where I like. Easy, quick and effective. I shave with straight razors and slickness is paramount - I find thickness of the lather to be detrimental.It's just because I wasn't shaving and wanted to show how much soap should be in the brush before building the lather. The point being that if you load too lightly and over hydrate that, you have no protection just wet slickness. Maybe I should have taken one picture of the brush with a load of lather and said, at least this much and been done with it. I didn't and I can't edit it now, I acknowledged that this was flawed a couple posts up.
I bought a Speick stick for the first time.My method:
Step 1: rub shave stick on wet face and neck.
It is just that easy. You may have to dip the tips of your brush to add a little bit more water depending on, but yes it is that easy.I bought a Speick stick for the first time.
Great! This is exactly the piece I was looking for. It is the best way? Is there any other methods to load soap with the brush?
This is the way.To be honest I feel this tutorial is going to confuse people more than help.
My method:
Step 1: rub shave stick on wet face and neck.
Step 2: lather with a damp brush.
Step 3: shave.
You could load your brush directly on the stick, but it's not convenient or recommended. You could make the stick into a puck and lather like a puck soap. I would only use this method if the soap is only available in stick form and you prefer to load from a puck.I bought a Speick stick for the first time.
Great! This is exactly the piece I was looking for. It is the best way? Is there any other methods to load soap with the brush?
Yes! This is what I experienced this morning when I shaved! Thank you!It is just that easy. You may have to dip the tips of your brush to add a little bit more water depending on, but yes it is that easy.
Really I wrote my post because I didn’t find practical load the brush directly on the stick.You could load your brush directly on the stick, but it's not convenient or recommended. You could make the stick into a puck and lather like a puck soap. I would only use this method if the soap is only available in stick form and you prefer to load from a puck.
But if you want to use the shave stick to it's full potential, rub it on your wet face, face lather with a damp brush and shave away.
Make sure lots of soap is caught in your whiskers, cheeks, neck, goatee area. If you need to reapply for pass 2 or 3, reapply. I find there is usually enough soap in the brush from the first application, it's rarely needed to reapply. But if you need to, just reapply the stick. Not as much will stick to your face on additional applications, as the whiskers will already be mowed down.
Oh yes lather will end up in all kinds of places in the bathroom, especially face lathering and using a synthetic brush. that is why I keep cleaning supplies in the bathroom so I do not cause myself some additional hardship.Really I wrote my post because I didn’t find practical load the brush directly on the stick.
This morning I tried for the first time to rub the stick on the wet face.
Then I lather with the damp brush but I need to optimize the brush humidity because this morning I splashed water on the mirror and I think you can imagine what the wife will tell you!