- Thread starter
- #1,841
Roughly 10 hours since shaving with the Jupiter and my face is as smooth as freshly shaved.
Remarkable!
Remarkable!
Last edited:
I think the Jupiter might have more exposure than the Outlaw Evolution, but in the Outlaw, I could feel the blade more, yet differently, very likely due to more blade flex.Man, it's hard to tell. Reggie's doesn't publish anything about blade exposure but from what I felt, it would be very very slight positive. Based on the efficiency I got, I'm guessing it is since neutral & negative razors typically aren't this efficient for me. But you barely feel any blade.
It's weird!
The Outlaw description says it's "neutral to slight posive, depending which blade is used"
But it definitely has more blade feel than the Reggie's Jupiter. And the old Outlaw had even more blade feel than the new Outlaw.
Hope this helps!
Yep, same results for me!I think the Jupiter might have more exposure than the Outlaw Evolution, but in the Outlaw, I could feel the blade more, yet differently, very likely due to more blade flex.
It's odd that the Outlaw has so much of it, though. The clamping surface should be large, but I think that the way the top cap is designed makes it err more on the side of less contact with the base plate's clamping point nearer the cutting edge, and the top cap is rounded upward a fair bit near the cutting edge, allowing for more upward flex.
Might be just the two pieces I got, though.
The Merkur Futur arrived from Portugal today!
Let's see how I get along with it this time around:
Chris, where'd you read that I had a clone?Ahh good, you got the real thing this time, the genuine article, not the fake clone. Now, it is true that the genuine Futur, does provide difficulty, in getting the under the nose whiskers. Having said that however, the weight of the Future, helps to produce a smooth shave with a GSB, Nacet, or Wizamet.
You will notice how the weight of the razor, carries the blade through the cut. But as Corey had to learn, use lower aggression levels first. Because at the end of the day, the Futur is an aggressive razor. So start with level 1 first, if its not enough, move onto level 2 or 3.
Ideally, you won't have seriously course whiskers, requiring you to use settings 4 through 6. One things for sure, clones don't always get it right, so its great that you finally have the genuine article now. Good luck to you, happy shaves. Thanks for sharing your pictures.
I suspect it's that you were able to keep the angle with it really well, better than with a lot of other razors, and the mildly positive exposure did the rest.Ok, so it's been around 21 hours since I shaved with the Reggie's Jupiter. I have a habit of feeling my face throughout different times of the day when trying out a new razor.
Now is that I'm feeling some stubble!
If it weren't for the fact that I need a close shave for work (and because I love to shave every day), I'd be able to get away with skipping a day.
Folks, this is as I stated, a 2 pass WTG/XTG with no ATG. I said it left me near BBS and was correct on that assumption right after I finished the shave last night.
So how'd they do it? I haven't a clue!
A razor that feels like barely nothing has touched your face during and after the shave but leaves a shave this close?
I guess Reggie's figured out some magic formula or something when it comes to designing a razor.
This razor is nothing short of phenomenal!
So how'd they do it? I haven't a clue!
That's possible but I seem to relatively do the same with most of my best & frequently used razors.I suspect it's that you were able to keep the angle with it really well, better than with a lot of other razors, and the mildly positive exposure did the rest.
Nailed it! That's the answer!!
It's a "Š" - an S with a caron on top .@Slapo
Question, sir.
May I ask what the symbol on your avatar is?
Hope your week is going well so far.
Yeah, it does seem confusing.Shave #2 with the Reggie's Jupiter!
My usual nightly 2 pass WTG/XTG, same Lab Blue blade with TOBS Mr. Taylor's cream.
Plenty of stubble left over from yesterdays shave with the Futur!
Again the same wonderful result as my first shave with the Jupiter.
I don't know what else to say except that this razor is exceptional.
The bad:
It's making me very curious about the Stainless version they make
But it's very expensive so I think if I go that route it'd be a future purchase.
The exchange rate with the British pound isn't very good now.
And that brings me to wonder about their pricing:
USD including shipping to the USA:
Aluminum Jupiter: $120
Brass Jupiter: $140 (I paid $126 because I used a first time buyer coupon)
Stainless Saturn: $294
Titanium Titan: $320
Does this pricing make sense to anyone?
Full polished brass with an amazing fit and finish and it's $20 more than the aluminum!
And then comparing the brass to the stainless:
I get the fact that Brass is easier to machine but the brass razor is fully polished which should bring up the cost.
And to get a stainless one it's $154 more than the brass. That's a massive jump in price!
And then the titanium is just $26 more than the stainless?
The whole pricing structure makes no sense to me.
In my view: the aluminum is OK at $120, the brass is a steal at $140, the stainless is overpriced (should be max $250) and the titanium should be $300.
That's what I believe it should be anyways, maybe they have their reasons for these prices.
For now, I will enjoy my incredible bargain priced brass razor!
I just read what I wrote. I think I made it confusing!Yeah, it does seem confusing.
View attachment 1831442
Yes. You have materials expenses and tooling expenses. Both metals are relatively soft so probably similar tooling expense; the raw material difference may really only be $20! More interesting is the difference between the other two, Henson has stated that they will not produce a stainless razor because it would cost as much as titanium. Nope, I ain't going back for another look... nope...Does this pricing make sense to anyone?
Full polished brass with an amazing fit and finish and it's $20 more than the aluminum!
Interesting!Yes. You have materials expenses and tooling expenses. Both metals are relatively soft so probably similar tooling expense; the raw material difference may really only be $20! More interesting is the difference between the other two, Henson has stated that they will not produce a stainless razor because it would cost as much as titanium. Nope, I ain't going back for another look... nope...
Work is pretty pricey in the UK, and I think the design of the steel and titanium heads makes them a bit trickier to machine than the Jupiter as well.Interesting!
I guess it makes sense then. I had no idea that making a stainless razor cost so much.
But then you have someone like The Goodfellas' smile that makes the fully stainless CNC machined Syntesi "in Italy" for under $100.
I wonder how they pull it off?
Maybe that stuff is all cheaper in Italy?
Which would make since brass Fatip's are dirt cheap.
Edit: And the Greencult's too which are made in Austria!
I was gonna throw Shield on the list of cheap fully stainless razors (Last week I ordered 2 in GEM & DE format for less than $60 a piece). But then I thought about it and it wouldn't be a fair comparison since stuff in China can be made for pennies on the dollar.
I guess it is what it is and I'll have to fork out the money for the stainless Reggie's if I decide to buy one down the line!